Banner SC22-3E Safety Controller with Ethernet Instrukcja Użytkownika Strona 60
- Strona / 130
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
5.1.4 Other Functions
Receive a Configuration from the Safety Controller
To receive a configuration from a Controller and display it in the PCI:
• Connect the Safety Controller to the PC using the USB cable.
• Apply 24V dc power to the Controller.
•
Click on the Receive button in the tool bar.
• If the configuration is not already confirmed, you may choose to confirm it at this time.
Send a Configuration to the Safety Controller
To send a configuration from the PCI to a Controller:
• Connect the Safety Controller to the PC, using the USB cable.
• Apply 24V dc power to the Controller.
•
Click on the Send button in the tool bar.
Open a Configuration from the XM Card
Both confirmed and unconfirmed configurations can be sent to or received from the XM card. To open a copy of a configuration from the
XM card and display it in the PCI:
• Connect the SC-XMP programming tool to the PC using the USB cable.
• Insert the XM card into the programming tool.
• Go to File > Open From XM Card in the upper-left corner of the screen.
A message will appear when the operation is complete.
Send a Configuration to the XM Card
Both confirmed and unconfirmed configurations can be sent to or received from the XM card. To send a copy of a configuration from the
PCI to the XM card (via the programming tool):
• Connect the SC-XMP programming tool to the PC using the USB cable.
• Insert the XM card into the programming tool.
•
Select the Open Folder button
in the tool bar and open the intended configuration file.
• Go to File > Send To XM Card in the upper-left corner of the screen.
A message will appear when the operation is complete.
Lock the XM Card
It is important to note that this operation cannot be undone. Once the card is locked, another configuration can never be stored on it. This
operation is useful when the XM card and its configuration will be transported to another Controller, or for storing and archiving a configu-
ration. To lock the XM card so that the stored configuration cannot be changed:
• Insert the XM card into the SC-XMP programming tool.
• Verify that the correct file is stored on the XM card.
• Go to File > Lock XM Card in the upper left of the tool bar.
A message will appear when the operation is complete.
SC22-3/-3E Safety Controller Instruction Manual
60 www.bannerengineering.com - tel: 763-544-3164 P/N 133487 rev. C
- Original Instructions 1
- Contents 2
- Contents 3
- 4 P/N 133487 rev. C 4
- Contents 5
- 1 About This Document 6
- 1.3 Standards and Regulations 7
- 1.4 Contact Us 8
- 2 Overview 9
- 2.1 Ethernet-Compatible Model 9
- 2.2 Applications 10
- 2.3 Design and Testing 10
- 2.4 Components 10
- 2.4.2 USB Connections 11
- 2.4.3 Ethernet Connections 11
- 2.4.4 SC-XMP Programming Tool 11
- 2.5.1 Onboard Interface (OBI) 12
- Accessing Fault Codes 14
- PCI Software Compatibility 15
- 2.6.2 Safety Outputs 16
- 2.6.3 Status Outputs 17
- 2.6.4 Virtual Status Outputs 17
- 2.7 System Settings 18
- 2.8 Internal Logic 19
- 2.9 Password Overview 20
- 3.3 Ethernet Cordsets 22
- 3.4 Interface Modules 22
- 3.5 Specifications 23
- 3.5.1 Dimensions 25
- 4 System Installation 26
- 4.1 Appropriate Application 26
- 4.3 Safety Input Devices 27
- SO1 SO2 SO3 28
- S = Simultaneous 29
- C = Concurrent 29
- Signal Change-of-State Types 30
- Signal Debounce Times 30
- 4.4 Non-Safety Input Devices 31
- 4.5 Input Device Resets 33
- 4.6 Safety Input Function 35
- 4.6.2 Two-Hand Control (THC) 36
- 4.6.3 Enabling Devices 36
- 4.6.4 Mute Function 37
- 4.6.5 Bypass Function 38
- 4.7.2 Safety Outputs 41
- Safety Input 42
- (ON-Delay) 42
- (OFF-Delay) 42
- (To SO 1A) 46
- (To SO 1B) 46
- 1A 1B 2A 2B 3A 3B A2 47
- 4.8 Status Outputs 50
- 4.9 Virtual Status Outputs 52
- 4.10 Commissioning Checkout 52
- 5.1.1 Configuration Tools 53
- 5.1.2 Build a Configuration 54
- Create a New Configuration 55
- Add an Input Device 55
- Finish the Configuration 57
- System Reset 59
- 5.1.4 Other Functions 60
- Export Documents 61
- Print Options 61
- Run Mode 63
- Configuration 63
- 6.2 Run Mode 64
- 6.3 Configuration Mode 64
- 6.3.3 Confirm Configuration 65
- 6.4 Edit Configuration 66
- 6.4.3 Outputs/System Settings 67
- 6.5 Add an Input 68
- 7.3.1 Run Mode Screen—OBI 72
- 7.4 Manual Reset 73
- 7.6 Reset Signal Requirements 74
- 8 System Checkout 75
- W1 W2 W3 W4 80
- 9.1 Cleaning 82
- 9 Troubleshooting 82
- 9.4 Recovering from a Lockout 86
- 9.5.1 Fault Log—PCI 87
- 9.5.2 Fault Log Recording—PCI 87
- 9.6.1 View Current Faults—OBI 88
- Device Name 89
- Fault Description 89
- Time Since Fault 89
- Fault Code 89
- Principles 90
- OFFON OFFON 91
- 10.2 Protective (Safety) Stop 92
- OpenOpen 95
- Open Open Open 96
- 24V 24V 24V 97
- 10.4 Optical Sensor 98
- 10.5 Two-Hand Control 100
- 10.6 Safety Mats 103
- Emergency Stop Hookup Options 108
- Category 2 E-Stop Circuit 108
- Category 3 E-Stop Circuit 108
- Category 4 E-Stop Circuit 108
- 10.8 Rope/Cable Pull 109
- S1 S2 S1 S2 111
- 10.9 Enabling Device 112
- ONOFF ONOFF 114
- Lockout/Tagout 115
- 10.11 Mute Sensor Pair 116
- Mute Device Requirements 117
- Inductive Proximity Sensors: 118
- 10.11.4 Mute Enable (ME) 119
- 10.11.5 Mute Lamp Output (ML) 119
- 10.11.7 Mute on Power-Up 120
- < 3s< 3s 122
- < 3s< 3s < 3s< 3s 123
- 11 Ethernet Reference 124
- 11.1 Ethernet Setting Access 124
- 11.3 Support Files 125
- Reserved 127
- 12 Glossary 128
Powiązane produkty i podręczniki dla Maszyny specjalne Banner SC22-3E Safety Controller with Ethernet
(4 strony)
(70 strony)
(2 strony)
(4 strony)Black & Decker BDPR400 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Black & Decker BDPR400.
Nous fournissons des manuels en pdf 1 Black & Decker BDPR400 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji