Banner SC22-3E Safety Controller with Ethernet Instrukcja Użytkownika Strona 62
- Strona / 130
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
6 Onboard Interface Configuration (OBI)
6.1 Onboard Interface (OBI) Overview
The Safety Controller’s onboard interface (OBI) consists of a display and six push buttons that are used to:
• Select a language
• Create, confirm, edit, erase, send, and receive a configuration
• Display real-time Run mode information
• Display current fault data, fault log data, and to clear the fault log
• Display the model number of the Safety Controller
• Set a password
The configuration is used to define the input devices that will be connected to the Safety Controller and to establish relationships between
input devices, and between the input devices and the outputs.
This section provides a “map” and description of Run mode and Configuration mode options, using the OBI. See the following figure for
an overview of all the Run mode and Configuration mode options available. For an example of a beginning-to-end configuration process
using the OBI, refer to the OBI tutorial in the SC22-3/-3E Configuration Tutorial, to be found at www.bannerengineering.com.
To move through the menus, in most cases, press the OK push button to make a selection or move further into the menu tree; press
the ESC push button to move up a step. When a vertical list of options appears on the screen, use the up/down arrow push buttons to
highlight an option to select. Press OK to select the highlighted option. When a single option appears on the screen (for example, an
input device) with an arrow running across the top of the screen, use the left/right arrow push buttons to step through the selections;
press OK to select the option showing on the screen.
SC22-3/-3E Safety Controller Instruction Manual
62 www.bannerengineering.com - tel: 763-544-3164 P/N 133487 rev. C
- Original Instructions 1
- Contents 2
- Contents 3
- 4 P/N 133487 rev. C 4
- Contents 5
- 1 About This Document 6
- 1.3 Standards and Regulations 7
- 1.4 Contact Us 8
- 2 Overview 9
- 2.1 Ethernet-Compatible Model 9
- 2.2 Applications 10
- 2.3 Design and Testing 10
- 2.4 Components 10
- 2.4.2 USB Connections 11
- 2.4.3 Ethernet Connections 11
- 2.4.4 SC-XMP Programming Tool 11
- 2.5.1 Onboard Interface (OBI) 12
- Accessing Fault Codes 14
- PCI Software Compatibility 15
- 2.6.2 Safety Outputs 16
- 2.6.3 Status Outputs 17
- 2.6.4 Virtual Status Outputs 17
- 2.7 System Settings 18
- 2.8 Internal Logic 19
- 2.9 Password Overview 20
- 3.3 Ethernet Cordsets 22
- 3.4 Interface Modules 22
- 3.5 Specifications 23
- 3.5.1 Dimensions 25
- 4 System Installation 26
- 4.1 Appropriate Application 26
- 4.3 Safety Input Devices 27
- SO1 SO2 SO3 28
- S = Simultaneous 29
- C = Concurrent 29
- Signal Change-of-State Types 30
- Signal Debounce Times 30
- 4.4 Non-Safety Input Devices 31
- 4.5 Input Device Resets 33
- 4.6 Safety Input Function 35
- 4.6.2 Two-Hand Control (THC) 36
- 4.6.3 Enabling Devices 36
- 4.6.4 Mute Function 37
- 4.6.5 Bypass Function 38
- 4.7.2 Safety Outputs 41
- Safety Input 42
- (ON-Delay) 42
- (OFF-Delay) 42
- (To SO 1A) 46
- (To SO 1B) 46
- 1A 1B 2A 2B 3A 3B A2 47
- 4.8 Status Outputs 50
- 4.9 Virtual Status Outputs 52
- 4.10 Commissioning Checkout 52
- 5.1.1 Configuration Tools 53
- 5.1.2 Build a Configuration 54
- Create a New Configuration 55
- Add an Input Device 55
- Finish the Configuration 57
- System Reset 59
- 5.1.4 Other Functions 60
- Export Documents 61
- Print Options 61
- Run Mode 63
- Configuration 63
- 6.2 Run Mode 64
- 6.3 Configuration Mode 64
- 6.3.3 Confirm Configuration 65
- 6.4 Edit Configuration 66
- 6.4.3 Outputs/System Settings 67
- 6.5 Add an Input 68
- 7.3.1 Run Mode Screen—OBI 72
- 7.4 Manual Reset 73
- 7.6 Reset Signal Requirements 74
- 8 System Checkout 75
- W1 W2 W3 W4 80
- 9.1 Cleaning 82
- 9 Troubleshooting 82
- 9.4 Recovering from a Lockout 86
- 9.5.1 Fault Log—PCI 87
- 9.5.2 Fault Log Recording—PCI 87
- 9.6.1 View Current Faults—OBI 88
- Device Name 89
- Fault Description 89
- Time Since Fault 89
- Fault Code 89
- Principles 90
- OFFON OFFON 91
- 10.2 Protective (Safety) Stop 92
- OpenOpen 95
- Open Open Open 96
- 24V 24V 24V 97
- 10.4 Optical Sensor 98
- 10.5 Two-Hand Control 100
- 10.6 Safety Mats 103
- Emergency Stop Hookup Options 108
- Category 2 E-Stop Circuit 108
- Category 3 E-Stop Circuit 108
- Category 4 E-Stop Circuit 108
- 10.8 Rope/Cable Pull 109
- S1 S2 S1 S2 111
- 10.9 Enabling Device 112
- ONOFF ONOFF 114
- Lockout/Tagout 115
- 10.11 Mute Sensor Pair 116
- Mute Device Requirements 117
- Inductive Proximity Sensors: 118
- 10.11.4 Mute Enable (ME) 119
- 10.11.5 Mute Lamp Output (ML) 119
- 10.11.7 Mute on Power-Up 120
- < 3s< 3s 122
- < 3s< 3s < 3s< 3s 123
- 11 Ethernet Reference 124
- 11.1 Ethernet Setting Access 124
- 11.3 Support Files 125
- Reserved 127
- 12 Glossary 128
Powiązane produkty i podręczniki dla Maszyny specjalne Banner SC22-3E Safety Controller with Ethernet
(4 strony)
(70 strony)
(2 strony)
(4 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.174 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji